6-30v Relay Module Switch Trigger Compatible With Time Delay Circuit Timer Cycle Adjustable
£9.55
Product Description
brand new and high qualityMaterial: Electrical componentsColor: See picturesProduct introduction:1. Operating voltage: 6--30V2. Trigger Signal Source: High Level Trigger (3.0 V-24 V), signal ground and system ground are not common, which can increase anti-interference abilit system (short circuit can also connect with a ground common)3. Output Capacity: can control no more than for DC 30V 5A AC or 220 V devices 5A4. Optocoupler Isolation: improve the anti-interference ability, after the parameter setting, it will memory foreverWarning: Relay contact is passive and electricity production; 1 channel has the control function on / off Operation mode:P1: After triggered signal, power relay on for time OP, then turn off; within the OP period following operation:1) P1.1: signal being triggered again is not effective2) P1.2: signal being triggered again, start for time again3) P1.3: signal being triggered again, reset; disconnect relay, stop timingP2: giving the trigger signal, the for time after shutdown relay CL power relay OP for time; then timing, turn off the relayP3.1: give the trigger signal after the power relay on for time OP, CL shutdown for time relay; then operating cycle above cycle gaive signal again, shutdown relay stop timing; cycle times (LOP) can be setP3.2: after connecting. no need to trigger signal, power relay on for time OP, CL shutdown for time relay; then the operating cycle above timea cycle (LOP) can be setQ4: keeping the function of the signal; if there is no trigger signal, the for time will be canceled, relay stay connected; when the signal disappears, timing OP turn off the relay; over for time, if no signal again, the for time is cleared for Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustablehow to choose the for time interval:in the selection of parameter set interface mode, and press the STOP button to select the for timexxx. if the decimal point is in some place, the for time interval is s-1 999 sxx. x is decimal place is ten, the for time interval is 0.1 s 99.9 s-x. x. x is the decimal point are all on, the for time interval is 1 min-999 minparameter Introduction: OP power over for time, turn off for time CL, LOP cycle times (1-999 times, "---" is unlimited cycle)How to set the parameter:1. First make sure relay operation mode2. According to the operaiting relay mode, the main interface (power module will flash current operating mode; standard mode P1.1, then come intot main interface); long press SET for key two seconds and then looen enter selection interface mode; by pressing UP, DOWN for key to choose the mode setting (P1.1 ~ P4)3. After selecting the mode, press short SET to set the corresponding parameter, then the parameter you want to set will flash (OP power in for time; CL power off for time; LOP cycle times, "---" is unlimited cycle ); by UP, DOWN to set the parameter value, support long press (increase or decrease quickly) and press slightly (increase or decrease of 1 unit); after setting the parameter value by short press the STOP for key to choose decimal place; choose the for time interval (corresponding for time interval is 0.1 s-999 min); Short press SET to set the current mode next parameter, the process is the same as above4. After the setting mode parameter, press and hold the SET button then hold the current configuration mode will flash, then go back to the main interface; define success parameter main interface: when the relay does not work, it will show "000" (no decimal point); the operating state relay, the screen has a decimal pointMode Select Interface: press and hold the SET for key to enter; after setting, long press the SET button back on main interface Expansion Function for Key STOP:Activate Relay mode:1. NO: PO in power over for time, relay can be connected2. OFF: relay is not allowed to connect, when in the off state in short main interface press the STOP for key to achieve turn ON and OFF, current state will flash; then back to the main interface (this function is a function of sudden stop, 1 for key to turn off the relay)Sleep Mode:C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program wellThe d-Normal Mode: nixie tube show everNote: Press and hold STOP button for 2 seconds can achieve change from C-P to O-d; Current state will flash and then return to the main interfaceSize: 6.3*3.8*1.5cm/2.48"*1.50"*0.59"No retail packageQuantity:1PcNote: Due to the difference between different monitors, the picture may not reflect the actual colorof the item. Thank you
6-30v Relay Module Switch Trigger Compatible With Time Delay Circuit Timer Cycle Adjustable
brand new and high qualityMaterial: Electrical componentsColor: See picturesProduct introduction:1. Operating voltage: 6--30V2. Trigger Signal Source: High Level Trigger (3.0 V-24 V), signal ground and system ground are not common, which can increase anti-interference abilit system (short circuit can also connect with a ground common)3. Output Capacity: can control no more than for DC 30V 5A AC or 220 V devices 5A4. Optocoupler Isolation: improve the anti-interference ability, after the parameter setting, it will memory foreverWarning: Relay contact is passive and electricity production; 1 channel has the control function on / off Operation mode:P1: After triggered signal, power relay on for time OP, then turn off; within the OP period following operation:1) P1.1: signal being triggered again is not effective2) P1.2: signal being triggered again, start for time again3) P1.3: signal being triggered again, reset; disconnect relay, stop timingP2: giving the trigger signal, the for time after shutdown relay CL power relay OP for time; then timing, turn off the relayP3.1: give the trigger signal after the power relay on for time OP, CL shutdown for time relay; then operating cycle above cycle gaive signal again, shutdown relay stop timing; cycle times (LOP) can be setP3.2: after connecting. no need to trigger signal, power relay on for time OP, CL shutdown for time relay; then the operating cycle above timea cycle (LOP) can be setQ4: keeping the function of the signal; if there is no trigger signal, the for time will be canceled, relay stay connected; when the signal disappears, timing OP turn off the relay; over for time, if no signal again, the for time is cleared for Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustablehow to choose the for time interval:in the selection of parameter set interface mode, and press the STOP button to select the for timexxx. if the decimal point is in some place, the for time interval is s-1 999 sxx. x is decimal place is ten, the for time interval is 0.1 s 99.9 s-x. x. x is the decimal point are all on, the for time interval is 1 min-999 minparameter Introduction: OP power over for time, turn off for time CL, LOP cycle times (1-999 times, "---" is unlimited cycle)How to set the parameter:1. First make sure relay operation mode2. According to the operaiting relay mode, the main interface (power module will flash current operating mode; standard mode P1.1, then come intot main interface); long press SET for key two seconds and then looen enter selection interface mode; by pressing UP, DOWN for key to choose the mode setting (P1.1 ~ P4)3. After selecting the mode, press short SET to set the corresponding parameter, then the parameter you want to set will flash (OP power in for time; CL power off for time; LOP cycle times, "---" is unlimited cycle ); by UP, DOWN to set the parameter value, support long press (increase or decrease quickly) and press slightly (increase or decrease of 1 unit); after setting the parameter value by short press the STOP for key to choose decimal place; choose the for time interval (corresponding for time interval is 0.1 s-999 min); Short press SET to set the current mode next parameter, the process is the same as above4. After the setting mode parameter, press and hold the SET button then hold the current configuration mode will flash, then go back to the main interface; define success parameter main interface: when the relay does not work, it will show "000" (no decimal point); the operating state relay, the screen has a decimal pointMode Select Interface: press and hold the SET for key to enter; after setting, long press the SET button back on main interface Expansion Function for Key STOP:Activate Relay mode:1. NO: PO in power over for time, relay can be connected2. OFF: relay is not allowed to connect, when in the off state in short main interface press the STOP for key to achieve turn ON and OFF, current state will flash; then back to the main interface (this function is a function of sudden stop, 1 for key to turn off the relay)Sleep Mode:C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program wellThe d-Normal Mode: nixie tube show everNote: Press and hold STOP button for 2 seconds can achieve change from C-P to O-d; Current state will flash and then return to the main interfaceSize: 6.3*3.8*1.5cm/2.48"*1.50"*0.59"No retail packageQuantity:1PcNote: Due to the difference between different monitors, the picture may not reflect the actual colorof the item. Thank you
Related Products
£7.33
£8.04
Amazon
£5.23
Amazon
£58.79
Amazon
£58.79
Amazon
£55.15
Amazon
£59.61
Amazon
£58.79
Amazon
£58.79
Amazon
£58.79
Amazon
£53.97
Amazon
Delivery, Returns & Refunds
Delivery
Sellers offer a range of delivery options, so you can choose the one that’s most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a seller’s listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Returns
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Refunds
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.